DE

Solo developer

Dull Edge Technologies

Documentation

Process

Home

A document for Process.

Processes

Overview

This goal of the project is to use be able to create custom PCBs with a technique that is scalable to microscopic scales. To achieve this an technique used in both PCB and semiconductor manufacturing is used with a novel technique planned for Via generation.

One of the key processes is photolithography that starts with an exposure step to make parts of the photoresist more or less resistant to the developer. So that when the board is exposed to the developer only the (none)exposed regions are removed, exposing the copper underneath. The entire board is then put in a etch bath (Typically some type of acid) this removes the exposed copper in theory leaving a precisely controlled copper pattern.

Then where inter layer connections are required holes are drilled, and then some type of electrical connection is made from one layer to the other (Typically done using some type of electro plating).

Process Steps.svg

Coat

Before the board can be exposed it must be coated with some type of photoresist. There are 2 main application methods that can be choose either dry film or liquid. The dry film photo resist is easy to procure and is applied with heat press step. A liquid resist can be applied using several different methods popular ones include spin coating, and squeegee.

Due to the easy of getting, lack of tooling required Dry film photo resist was chosen to start with a plan to transition to liquid resist later on for easy of automatic handling. Exact film is believed to be ETERTEC® TPR2600R or comparable (the provider does not provide a SKU)

Exposure

There are two main families of exposure tools, masked and maskless. A masked tool uses a pattern that is already cut into either a mirror or a patterned opaque material on a clear substrate . A maskless tool uses some type light control to emit any number of pattern with out needing a new mask.

MaskedMaskless
Design preparationCreation of a maskPrepare digital pattern
LifetimeThe light sourceThe light source and controlling mechanism
Equipment ComplexityLow - MediumHigh*
ResolutionDependent on optics and maskDependent on pixel size
Automation potentialPossiblePossible; Pattern can be changed digitally

*A DLP projector can be found cheaply and is already made

Due to the want for quickly changing between designs a maskless process was chosen. This still leaves open the choice of which particular light controlling mechanism is used.

GalvoDLPLCD
ResolutionHighLowModerate
Equipment ComplexityHighLow/Moderate*Low/Moderate*
SpeedSlowWhole Field at onceWhole Field at once
CostLowHigh*Moderate*
LifetimeLongMediumShort

*A projector can be found cheaply and is already made

For ease of construction and pre-existing works a DLP projector was chosen. The required modifications were the removal of the color wheel and the UV Filter directly on the lamp. The addition of a UV Hot pass mirror would extend the projected life time (this is due to reducing the temperature of the optical train).

Develop

The current development process uses an un-temperature controlled sodium carbonate solution and a blind timing. This in the future should be replaced with an actively monitored system to measure the breakpoint, solution loading, and active temperature control.

Etch

There are 3 main families of etching processes Wet, Dry, and Laser. Wet etching uses liquid chemical to dissolve the copper typically some type of chloride; Dry etching uses a plasma or ion beam to remove the copper; Laser etching uses a high energy laser to ablate unwanted material away. There is a fourth option of mechanical milling but has a limited resolution and required equipment.

CriteriaWetDryLaser
Typical Resolution0.025mm0.013mm0.0025mm
ComplexityLowHighModerate
Equipment costLowHighHigh
Running costModerateLow-ModerateLow
WasteChemical waste dependent on chemistryNoneNone
Other NotesDoesn't require a mask

Due to low cost and simplicity of use, a wet etch process was selected. Then several different possible chemistries were evaluated.

Within the family of wet etch processes there are several prominent etchants. The three I considered where ferric chloride, cupric chloride, and ammonium persulfate.

ChemistryCostWasteDanger
Ferric ChlorideLowFerrous Chloride & Copper (II) ChlorideModerate
Cupric ChlorideModerateCopper(I) ChlorideModerate
Ammonium PersulfateModerate-HighCopper(II) Sulfate & Ammonium SulfateHigh

Ferric Chloride was choosen for initial testing due to ease of procurment and low cost. However cupric chloride is a very promising long term choice, due to the waste stream being Copper(I) Chloride it is possible to regenerate it using a electrolysis proccess. How ever the increase in cost does not make it favorable as a initial choice.

Drilling

Currently drilling is done using a 3d printed jig. This has a low precision and is a manual process. There are plans to replace this with a automated tool. However that tool won't be made until at earliest stage 3.

Plating

Currently plating is planned to be done using individual strands of copper. With a future transfer to some variation of a electro plating process. The exact electroplating process is currently under consideration.

Summary

Currently the system is capable of producing a board, but not a good board nor automatically.

ProcessTechniqueAutomated
CoatDry filmNo
ExposureDLP ProjectorPartially
DevelopSodium carbonateNo
EtchFerric ChlorideNo
Drilling3D Printed JigNo
PlatingManual solderingNo

Planned Process Steps

As described the board is missing a solder mask, silk screen, and support for multiple layers. Many of these should be capable of being done using a modified photolithography process using a different photo resist. But this planned for after boards are reliably manufactured.